Millennium 4 Remote Programming

Programming your remote control allows you to control your TV and VCR as well as your digital cable box.

Two notes before you begin:

  1. Many TVs and VCRs have more than one code listed. For these, start with the first code. If that doesn't work, try the second code and so on.
  2. After entering a correct device code, the TV or VCR mode indicator light will blink three times. If the TV or VCR mode light turns off, the code is invalid.
Which device would you like to setup?
Programming for your TV:

1. Click on the arrow below to find and highlight your TV manufacturer from the pull-down menu below:

2. On the remote control, press and hold TV until the four mode indicator lights flash twice (approx. 6 seconds).

3 Now enter the 4-digit code shown below:

Many devices have more than one code listed. For these, start with the first code. If that doesn't work, try the second code, and so on.

The TV's indicator should flash twice. If it doesn't, press TV as described above and try again with the next code. For example, if you have a JVC model, press and hold TV until the four mode indicators flash twice, then press 0-0-5-3.

4. After you have entered the correct code, point the remote at your TV and press POWER. If your TV turns on or off, you are finished programming for your TV.

If you have tried all the codes listed for your TV and it still does not turn on or off, click here.

Programming for your VCR:

1. Click on the arrow below to find and highlight your VCR manufacturer from the pull-down menu below:

2. On the remote control, press and hold VCR until the four mode indicator lights flash twice (approx. 6 seconds).

3 Now enter the 4-digit code shown below:

Many devices have more than one code listed. For these, start with the first code. If that doesn't work, try the second code, and so on.

The VCR's indicator should flash twice. If it doesn't, press VCR as described above and try again with the next code. For example, if you have a JVC model, press and hold VCR until the four mode indicators flash twice, then press 0-0-6-7.

4. After you have entered the correct code, point the remote at your VCR and press POWER. If your VCR turns on or off, you are finished programming for your VCR.

If you have tried all the codes listed for your VCR and it still does not turn on or off, click here.

Programming for your TV/VCR Combo:

Note: Some TV/VCR combinations may require a second TV code to control volume. Check the codes below and follow the instructions in Programming for your TV using the supplied TV code. If there is no TV code listed for your TV/VCR combo's operating code, you will need to use the volume control capabilities of your digital cable box.

1. Click on the arrow below to find and highlight your TV/VCR manufacturer from the pull-down menu below:

2. On the remote control, press and hold VCR until the four mode indicator lights flash twice (approx. 6 seconds).

3 Now enter the 4-digit code shown below:

Many devices have more than one code listed. For these, start with the first code. If that doesn't work, try the second code, and so on.

The TV/VCR's indicator should flash three times. If it doesn't, press VCR as described above and try again with the next code. For example, if you have a Sears TV/VCR, press and hold VCR until the four mode indicators flash twice, then press 0-0-0-0.

4. After you have entered the correct code, point the remote at your TV/VCR and press POWER. If your TV/VCR turns on or off, you are finished programming for your TV/VCR.

If you have tried all the codes listed for your VCR and it still does not turn on or off, click here.

Programming for your DVD Player:

1. Click on the arrow below to find and highlight your DVD manufacturer from the pull-down menu below:

2. On the remote control, press and hold DVD/VCR until the four mode indicator lights flash twice (approx. 6 seconds).

3 Now enter the 4-digit code shown below:

Many devices have more than one code listed. For these, start with the first code. If that doesn't work, try the second code, and so on.

The DVD player's indicator should flash twice. If it doesn't, press VCR as described above and try again with the next code. For example, if you have a JVC model, press and hold DVD/VCR until the four mode indicators flash twice, then press 0-5-5-8.

4. After you have entered the correct code, point the remote at your DVD player and press POWER. If your VCR turns on or off, you are finished programming for your DVD player.

If you have tried all the codes listed for your VCR and it still does not turn on or off, click here.